采用八叉树和OSG分页结点的海量点云三维可视化

针对现有海量点云可视化方法存在索引构建时间长、内存占用大等问题，研究一种八叉树索引结合OSG分页结点的快速可视化方法，可在占用较小内存的基础上快速建立点云索引并实时调度。采用八叉树索引结构对海量点云进行数据组织，建立各层级的八叉树结点并以文件映射的方式分块保存，对结点文件重组织转换为支持OSG渲染引擎的多分辨率点云数据。采用基于OSG分页结点的实时调度技术，对海量点云进行高质量可视化。与目前两款主流的点云数据处理商业软件进行实验对比分析，结果表明所提方法具有索引建立速度快、内存占用小等优点，同时可视化交互更加流畅，适用于各种配置计算机下海量点云数据的调度管理与实时可视化。     

焊缝表面缺陷激光扫描三维重构测量

为检测工件焊缝表面缺陷，采用点激光位移传感测距法和数据拟合技术进行焊缝表面缺陷检测试验研究. 首先采集缺陷表面轮廓数据点，利用高斯滤波对原始数据降噪处理. 再对处理后的数据点进行Delaunay三角剖分，使散乱点连接并结合其空间坐标重构出缺陷的三维模型. 结果表明，基于点激光位移传感测距技术及焊缝表面缺陷三维重构方法可以准确判断焊缝成形情况.     

Q690钢焊接接头微观组织对冷裂纹的影响研究

分析了Q690钢手工电弧焊与气体保护焊焊接冷裂纹产生与微观组织的联系。结果表明: 焊接冷裂纹起源于斜Y坡口根部, 沿熔合区、焊缝扩展至焊缝表面;2种工艺焊接的接头组织硬度均较母材高, 而塑性较差。热影响区为马氏体、贝氏体与铁素体混合组织, 焊缝组织由先共析铁素体、侧板条铁素体、贝氏体和针状铁素体等组成, 针状铁素体抗裂纹扩展能力较其他组织强。在2种焊接方法对应断口中观察到了冷裂纹起裂、扩展与断裂区的不同形貌, 起裂与扩展区存在塑性变形, 而断裂区为解理断裂。     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

高强铝合金双脉冲VPPA焊缝成形机理

建立双脉冲VPPA(variable polarity plasma arc)焊接系统，进行7A52高强铝合金双脉冲VPPA焊接工艺试验，研究低频脉冲调制叠加高频脉冲对VPPA焊接过程中焊缝成形和焊缝力学性能的影响. 结果表明，低频脉冲周期性振荡液态熔池，可获得表面饱满的鱼鳞纹焊缝；高频脉冲使电弧更为集中，有效地提高了电弧能量密度，穿透力加强；双脉冲耦合振荡加强了对熔池的搅动作用细化了铝合金焊缝晶粒. 焊接接头抗拉强度达到384.13 MPa，相比VPPA焊接接头强度提高了10.21%左右；焊接接头断面收缩率和断后伸长率均有一定程度的提高. 铝合金双脉冲VPPA焊接工艺提高了焊接接头力学性能.     

Attribute Allocation and Retrieval Scheme for Large-Scale Sensor Networks

Wireless sensor network is an emerging technology that enables remote monitoring of large geographical regions. In this paper, we address the problem of distributing attributes over such a large-scale sensor network so that the cost of data retrieval is minimized. The proposed scheme is a data-centric storage scheme where the attributes are distributed over the network depending on the correlations between them. The problem addressed here is similar to the Allocation Problem of distributed databases. In this paper, we have defined the Allocation Problem in the context of sensor networks and have proposed a scheme for finding a good distribution of attributes to the sensor network. We also propose an architecture for query processing given such a distribution of attributes. We analytically determine the conditions under which the proposed architecture is beneficial and present simulation results to demonstrate the same. To the best of our knowledge, this is the first attempt to determine an allocation of attributes over a sensor network based on the correlations between attributes.     

Performance characteristics of cascaded delay‐line node architectures in single‐path interconnection networks

Internally buffered multistage interconnection network architectures have been widely used in parallel computer systems and large switching fabrics. Migration from electrical domain to optical domain has raised the necessity of developing node architectures with optical buffers. Cascaded fibre delay line architectures can be seen as possible realizations of output and shared buffering in a 2 × 2‐switching element. These approaches can be used as buffered node architecture in a Banyan like interconnect. In this paper, we investigate and compare these approaches by using simulation methods. Different performance metrics, such as normalized throughput, average packet delay, packet loss rate and buffer utilization have been used under uniform and non‐uniform traffic models. Results show that the TC‐chain node Banyan network offer an improved normalized throughput and average packet delay performances under both traffic models without disrupting first‐in‐first‐out order of arrivals. The switched delay‐line requires fewer switching elements than TC and TTC architectures but at the cost of high packet delay. Copyright © 2004 John Wiley & Sons, Ltd.     

双滑动氧枪的应用

叙述了φO114双焊缝氧枪存在的问题及改型后单焊缝双滑动氧枪的优点及使用效果。     

超媒体系统中的人工智能方法

一、什么是超媒体近年来迅速崛起的多媒体(multimedia)技术,是一种使计算机具有交互式地综合处理和管理文字、图形、图象、声音、视频等多种媒体能力的技术,必将使计算机技术发生一     

微量元素对管道焊缝性能的改善

在焊条中添加微量元素Ce、Y、Ca、Ba和Zr，有利于改善石油天然气管道焊缝的金属性能，俄罗斯专家对此做了一系列实验和研究。结果表明添加微量元素有利于提高焊缝金属平面应变断裂韧性KIC，提高裂纹张开位移δc，减小裂纹扩展速率dα／dN改善焊缝金属的组织结构。通过大量的试验和研究，俄罗斯焊接学者确定了焊缝中微量元素的最佳含量，并建立了相关参数的数学模型。